The Stabilising Jacks are designed for use with Caravans, Motorhomes, Trailers and Specialist Vehicles requiring a steadying load capacity of 450 kg per jack. Fashioned in steel and protected by galvanised finish, this stabilising jacks differ from the traditional scissors design and affords notable practical advantages

in operation. Just a few seconds are needed to move the jacks into the operating or the stowed travelling position.

* The jacks can be bolted (preferred method) or welded. Bolt the mounting flange to a suitable surface

using self-locking nuts and bolts. In selecting a suitable position always take into consideration the 450-kg load capacity per jack.

* In some situations it may prove necessary to fabricate a bracket off the chassis/body to mount the jacks. In

this case make sure it is sufficient to take the 450-kg per jack loading.

* NB : in the stowed position, the jacks require a minimum inboard clearance of 350mm for model 45, and

450mm for model 55 (see fig 2).

* The jacks have two detent positions, stowing horizontally for traveling and angled downwards for use.

* Simply pull the leg to the point of freeing the spring-loaded catch from the detent slot. Lock the leg in the

jacking position detent.

* Lower the leg initially by holding down the locking tab and allowing inner jack tube to slide out to rest on the ground.

* Insert the jack rod through the front socket (fig3), ENSURING THAT THE END LOCATES IN THE SOCKET IN THE REAR WALL OF THE LEG, and apply downward hand pressure, with little effort the inner leg will extend down. Repeat the action until the vehicle or trailer is stable.

* To release the jacks, apply pressure to the locking tab, which can be loosened by tapping smartly with the rod if need be. The leg can now be retracted by hand without difficulty and swung upwards to lock automatically in the stowed position (fig 2)

Material: Heavy gauge steel

Protection: Zinc plated

Jack pad footprint: 25cm 2 per jack

Adjustment: MDL 45 290mm to 450mm

MDL 55 390mm to 550mm

The jacks are available in pairs, packaged as a kit with one jacking rod.

Level blocks are designed to level up your vehicle on uneven pitches. Simply place the leveling

chocks in front of the wheel you wish to raise and drive up the ramp slowly. Made of strong plastic,

they are easy to clean and will not corrode. SUPPLIED 2 X BLOCKS IN A NEAT STORAGE BAG.

As the world’s leading manufacturer of recreational vehicle awnings, Dometic has covered all approaches to

motorhome awnings. This new motorhome awning eclipses its competitors by doing away with inconvenient

support struts. This means you can use the entire space in front of your recreational vehicle. It completely

eliminates the awkward, time-consuming setup of conventional awnings.

Both the Manual & Electric awnings show-stopper is the arm joint manufactured from forged steel – patent

pending. This focal component of the ingenious mechatronics facilitates use of the awning without support struts. The electric variant of the Dometic Premium Awning is an innovation that is particularly convenient and safe. The electric version in particular is thus the benchmark regarding convenience and safety, fully automatic and operated at the touch of a button on the remote control. Also as standard on electric models is a wind sensor automatically retracts the awning when wind force reaches critical levels.

• Sleek Look, Light Weight

• Same Small box design no matter the awning length

• Mounts using awning rail or mounting brackets

• Support arms adjust easily with flip lock controls

• Patented floating roller technology that keeps roll tube straight and canopy tight

• Features sturdy Aluminium Case and end caps- No Plastic!

• Full or partial extension- if you don’t have the space to fully extend, you can stop at any point and set up the Freedom Awning

• Manual override on 12v model in case of power loss

The Carefree Freedom Awning is available in Wall or Roof Mount Versions. It can be operated by simply holding a button (12 volt models) or by easily winding the crank. Due to the arms being stored within the lead bar they are never far from reach. There is a choice of 3 magnificent hardware colours and 2 stunning vinyl options. If you already have a Freedom Manual awning and would like the Electric Version then don't despair! Upgrading to an Electric Version is easy. All you would need is the 12v Upgrade Kit, which will fit into your existing Carefree awning hardware.